catalog 1308028 issued 01-05 plug-in relays mini iso relays power relay f4 please observe the disclaimer. 32 powertrain systems chassis systems safety security body driver information convenience car industry truck industry other industry 134_kop1 description features limiting continuous currents 60/40 a at the no / nc con- tacts dimensional characteristics and the functional allocations of the plug-in terminals to iso 7588 standardized dimensions 24 v versions with contact gap > 0.8 mm plug-in or pcb terminals typical applications ignition lock lamp load (headlights) cooling fan abs exhaust emission control cross carline up to 60 a fuel pump engine cooling fan a/c blower a/c compressor clutch also available for 42 v applications please contact tyco electronics for relay application support. design dustproof; protection class ip 54 to iec 529 (en 60 529); with either mounting bracket or mounting clip options shrouded and weatherproof covers weight approx. 1.2 oz. (35 g) nominal voltage 12 v or 24 v; other nominal voltages available on request terminals quick connect terminals similar to iso 8092-1 coil and load 6.3 x 0.8 mm; surfaces tin-plated or pcb terminals accessories connectors see page 188 special models on request integrated components: resistor, varistor, diode special labels special cover shapes conditions all parametric, environmental and endurance tests are performed according to eia standard rs-407-a at standard test conditions unless otherwise noted: 23 c ambient temperature, 20-50% rh, 29.5 1.0" hg (998.9 33.9 hpa). please also refer to the application recommendations in this catalog for general precautions. disclaimer all technical performance data apply to the relay as such, specific conditions of the individual application are not considered. please always check the suitability of the relay for your intended purpose. we do not assume any responsibility or liability for not complying herewith. we recommend to complete our questionnaire and to request our technical service. any responsibility for the application of the product remains with the customer only. all speci fications are subject to change without notification. all rights of tyco are reserved.
for the make contact (2 x pin 87), pin 87a = 87. for the twin make contact, pin 87a = 87b. *) .666 .012 (16.9 0.3) .157 .012 (4.5 0.3) .315 .010 (8.4 0.25) .705 .010 (17.9 0.25) .315 .010 (8.0 0.25) .106 .020 (2.7 0.5) ecr1655-h plug-in relays mini iso relays power relay f4 please observe the disclaimer. 33 catalog 1308028 issued 01-05 dimensional drawing version with quick connect terminals version with pcb terminals view of the terminals (bottom view) view of the terminals (bottom view) mounting hole layout
plug-in relays mini iso relays power relay f4 please observe the disclaimer. 34 catalog 1308028 issued 01-05 load limit curve pin assignment load limit curve 1 ^ = arc extinguishes during transit time (changeover contact) load limit curve 2 ^ = safe shutdown, no stationary arc (make contact) 1 make contact/ 1 form a power relay f4 only 1 double make contact/ 1 form u power relay f4 only 1 make contact (2 x pin 87)/ 1 form a (2 x pin 87) 1 changeover contact/ 1 form c models with resistor or diode in parallel to the coil on request. models with resistor or diode in parallel to the coil on request. models with resistor or diode in parallel to the coil on request. *) models with resistor or diode in parallel to the coil on request. contact data contact configuration circuit symbol (see also pin assignment) rated voltage rated current at 85 c contact material max. switching voltage/power max. switching current 1) on 2) off min. recommended load 4) voltage drop at 10 a (initial) no contact nc contact mechanical endurance (without load) electrical endurance (example of resistive load) max switching rate at nominal load 6 operations per minute (0.1 hz) 1) the values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5 v for 12 v or 27 v for 24 v load voltages. 2) for a load current duration of maximum 3 s for a make/break ratio of 1:10. 3) special high performance 24 v version with contact gap > 0.8 mm, part number v23134-a0056-x432/-x433 (see ordering information). 4) see chapter diagnostics in our application recommendations on page 18. make contact/ double make contact/ changeover contact/ form a or form a (2x87) form u form c or 12 v 24 v 12 v 24 v 12 v 24 v 24 v 3) 40 a 20 a 2 x 25 a 2 x 15 a 30/40 a 15/20 a 20/30 a agni0.15 agni0.15 agni0.15 agsno 2 see load limit curve nc/no nc/no nc/no 120 a 120 a 2 x 100 a 2 x 100 a 45/120a 45/120a 45/120a 60 a 20 a 2 x 40 a 2 x 15 a 40/60a 15/20a 20/30a 1 a at 5 v typ. 15 mv, 200 mv max. typ. 2 x 15 mv, 200 mv max. typ. 15 mv, 200 mv max. typ. 20 mv, 250 mv max. > 10 7 operations > 2 x 10 5 > 1 x 10 5 > 2 x 10 5 > 1 x 10 5 > 2 x 10 5 > 1 x 10 5 > 1 x 10 5 operations operations operations operations operations operations operations 40 a, 14 v 20 a, 28 v 2 x 25 a, 14 v 2 x 15 a, 28 v 40 a, 14 v 20 a, 28 v 30 a, 28 v (no contact) (no contact) (no contact) > 5 x 10 5 operations 10 a, 28 v (nc contact)
plug-in relays mini iso relays power relay f4 please observe the disclaimer. 35 catalog 1308028 issued 01-05 coil data available for nominal voltages 12, 24 v nominal power consumption of the unsuppressed coil at nominal voltage 1.6 w nominal power consumption at nominal voltage with suppression resistor 1.8/2.1 w (standard/high performance 24 v) test voltage winding/contact 500 vac rms ambient temperature range 40 to + 125 c operate time at nominal voltage typ. 7 ms release time at nominal voltage 1) typ. 2 ms 1) for unsuppressed relay coil n.b. a low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. mechanical data cover retention axial force 150 n (33.8 lbs) pull force 200 n (45 lbs) push force 200 n (45 lbs) terminals pull force 100 n (22.5 lbs) push force 100 n (22.5 lbs) resistance to bending, force applied to front 10 n (2.25 lbs) 1) resistance to bending, force applied to side 10 n (2.25 lbs) 1) torsion 0.3 nm enclosures dust cover protects relay from dust. for use in passenger compartment or enclosures shrouded dust cover protects relay and relay connector (order separately) from dust and splash weatherproof cover mates with a connector (order separately) to seal relay from salt spray etc. recommended for under hood application 1) values apply 2 mm from the end of the terminal. when the force is removed, the terminal must not have moved by more than 0.3 mm. operating voltage range does not take into account the temperature rise due to the contact current e = pre-energization ambient temperature vs. coil voltage for continuous duty 100 90 80 70 60 50 40 90 95 100 105 110 115 120 125 130 135 140 145 150 applied coil voltage (% of nominal voltage) maximum allowable ambient temperature ( c) 30 110 120 130 0 a contact load 8 a contact load 16 a contact load 24 a contact load 32 a contact load 40 a contact load 134_atcv battery voltage
catalog 1308028 issued 01-05 plug-in relays mini iso relays power relay f4 36 please observe the disclaimer. ordering information (production in europe, asia and south america) part numbers (see table below for coil data) contact contact enclosure special relay part number tyco order number arrangement material features 12 v plug-in relays v23134-a0052-c643 2-1393302-2 1 form c agni0.15 dust cover v23134-a0052-x205 3-1393302-6 1 form c agni0.15 dust cover diode v23134-a0052-x278 4-1393302-1 1 form c agni0.15 dust cover resistor 560 ? v23134-a1052-c643 5-1393302-8 1 form c agni0.15 dust cover bracket v23134-a1052-x828 *) 7-1393305-5 1 form c agni0.15 sealed bracket, resistor 680 ? v23134-b0052-c642 7-1393302-5 1 form a agni0.15 dust cover v23134-b1052-c642 3-1393303-4 1 form a agni0.15 dust cover bracket v23134-b1052-x824 *) 6-1393305-9 1 form a agni0.15 dust cover bracket, resistor 680 ? v23134-c0052-c642 3-1393303-9 1 form a (2 pins 87) agni0.15 dust cover v23134-c1052-c642 4-1393303-7 1 form a (2 pins 87) agni0.15 dust cover bracket v23134-m0052-c642 5-1393304-6 1 form u agni0.15 dust cover v23134-m1052-c642 7-1393304-1 1 form u agni0.15 dust cover bracket 24 v plug-in relays v23134-a0053-c643 5-1393302-1 1 form c agni0.15 dust cover v23134-a0056-x432 1-1414167-0 1 form c agsno2 dust cover contact gap > 0.8mm, diode v23134-a0056-x433 1-1414168-0 1 form c agsno2 dust cover contact gap > 0.8mm, resistor 1.2 k ? v23134-a0064-x816 *) 5-1393305-3 1 form c agni0.15 sealed resistor 2.7 k ? v23134-a1053-c643 6-1393302-3 1 form c agni0.15 dust cover bracket v23134-a1064-x829 *) 0- 1432219-1 1 form c agni0.15 sealed bracket, resistor 2.7 k ? v23134-a1064-x830 *) 8-1393305-4 1 form c agni0.15 dust cover bracket, diode v23134-b0053-c642 0- 1393303-9 1 form a agni0.15 dust cover v23134-b1053-c642 3-1393303-7 1 form a agni0.15 dust cover bracket v23134-c0053-c642 4-1393303-4 1 form a (2 pins 87) agni0.15 dust cover v23134-c1053-c642 5-1393303-0 1 form a (2 pins 87) agni0.15 dust cover bracket v23134-m0053-c642 6-1393304-7 1 form u agni0.15 dust cover v23134-m1053-c642 7-1393304-4 1 form u agni0.15 dust cover bracket *) marking according to vf4 shematic. operating conditions temperature range, storage test climatic cycling with condensation temperature cycling damp heat cyclic constant corrosive gas vibration resistance shock resistance load dump jump start drop test flammability overload current 2) 1) fmvss: federal motor vehicle safety standard. 2) current and time are compatible with circuit protection by a typical 40 a automotive fuse. relay will make, carry and break the s pecified current. -40 c to 155 c relevant standard testing as per dimension comments en iso 6988 6 cycles storage 8/16 h iec 68-2-14 nb 10 cycles 40/+ 85 c (5 c per min.) iec 68-2-30 db, variant 1 6 cycles upper air temperature 55 c iec 68-2-3 ca 56 days iec 68-2-42 10 2 cm 3 /m 3 so 2 10 days iec 68-2-43 1 0.3 cm 3 /m 3 h 2 s 10 days iec 68-2-6 (sine sweep) 10-500 hz no change in the min. 5 g switching state > 10 s iec 68-2-27 (half sine pulse form) min. 20 g valid for nc contacts, 11 ms no contact values significantly higher iso 7637-1 (12 v) test pulse 5 vs =+ 86.5 v iso 7637-2 (24 v) test pulse 5 vs =+ 200 v 24 v for 5 minutes conducting nominal current at 23 c capable of meeting specifications after 1.0 m (3.28 foot) drop onto concrete ul94-hb or better (meets fmvss 302) 1) 54 a, 1800 s 80 a, 5 s 140 a, 0.5 s 240 a, 0.1 s
plug-in relays mini iso relays power relay f4 please observe the disclaimer. 37 catalog 1308028 issued 01-05 ordering information (production in europe, asia and south america) coil must must coil data rated coil resistance operate release allowable overdrive 1) for power relay f4 voltage +/- 10% voltage voltage voltage (v) (v) ( ? ) (v) (v) at 23 ? at 85 ? v23134-**052-**** 12 91 7.2 1.6 23 18 v23134-**053-**** 24 332 14.4 3.2 44 34 v23134-**056-**** 24 275 16.0 4.0 38 30 v23134-**064-**** 24 345 14.4 2.4 40.5 31.5 1) allowable overdrive is stated with no load applied and minimum coil resistance. coil versions part numbers (see table below for coil data) contact contact enclosure special relay part number tyco order number arrangement material features 12 v pcb relays v23134-a0052-g243 2-1393302-3 1 form c agni0.15 dust cover v23134-a0052-x812 *) 4-1393305-5 1 form c agni0.15 sealed v23134-a0052-x813 *) 4-1393305-7 1 form c agni0.15 sealed resistor 680 ? v23134-b0052-g242 7-1393302-7 1 form a agni0.15 dust cover v23134-b0052-x802 *) 2-1393305-2 1 form a agni0.15 sealed v23134-c0052-g242 4-1393303-0 1 form a (2 pins 87) agni0.15 dust cover v23134-m0052-g242 5-1393304-7 1 form u agni0.15 dust cover 24 v pcb relays v23134-a0053-g243 5-1393302-2 1 form c agni0.15 dust cover v23134-a0064-x820 *) 5-1393305-9 1 form c agni0.15 sealed v23134-b0053-g242 1-1393303-0 1 form a agni0.15 dust cover v23134-c0053-g242 4-1393303-5 1 form a (2 pins 87) agni0.15 dust cover v23134-m0053-g242 6-1393304-8 1 form u agni0.15 dust cover *) marking according to vf4 shematic. standard delivery packs (orders in multiples of delivery pack) power relay f4 quick connect verson: 315 pieces quick connect with bracket: 200 pieces pcb version: 200 pieces
|
